PRODUCTS
-
Hydraulic Sealing Elements
- SSE
- SSE/C
- SSA
- SSB
- SSN
- SSB-1
- SSG
- SSJ
- SSD
- SSM-1
- SSG-2
- SSO
- SSP
- SSQ
- SSD-3
Hydraulic Rod Sealing Elements
-
Pneumatic Sealing Elements
-
Guiding Elements
-
Static Sealing Elements
-
Special Sealing Elements
-
SealXpress Tailor-Made Machined Seals
SPC-1
| SEALX NO | D (H11) | d (h9) | B (-0/+0,2) | S(-0/+0,2) | A(-0/+0,1) | ds(h8) | d2 (+0/-0,2) | d1(± 0,1) | n |
| SPC-1-032 | 32,00 | 20,00 | 10,00 | 6,35 | 3,10 | 28,50 | 15,80 | 29,80 | 5 |
| SPC-1-035 | 35,00 | 22,00 | 10,00 | 6,35 | 3,10 | 31,40 | 17,80 | 32,80 | 5 |
| SPC-1-038 | 38,00 | 25,00 | 10,00 | 6,35 | 3,10 | 34,45 | 20,80 | 35,80 | 5 |
| SPC-1-040 | 40,00 | 26,00 | 9,40 | 6,35 | 3,10 | 35,40 | 21,60 | 37,80 | 5 |
| SPC-1-045 | 45,00 | 30,00 | 9,50 | 6,35 | 3,10 | 40,40 | 25,80 | 42,80 | 5 |
| SPC-1-045/1 | 45,00 | 35,00 | 8,50 | 6,35 | 3,10 | 42,00 | 30,80 | 42,80 | 5 |
| SPC-1-050 | 50,00 | 30,00 | 14,50 | 6,35 | 3,35 | 44,30 | 25,80 | 47,50 | 5 |
| SPC-1-055 | 55,00 | 40,00 | 11,00 | 6,35 | 3,10 | 50,40 | 35,80 | 52,80 | 5 |
| SPC-1-060 | 60,00 | 40,00 | 14,50 | 6,35 | 3,35 | 54,16 | 36,10 | 57,50 | 5 |
| SPC-1-063 | 63,00 | 45,00 | 11,00 | 6,35 | 3,10 | 58,40 | 40,84 | 60,50 | 5 |
| SPC-1-063/1 | 63,50 | 47,62 | 9,52 | 6,35 | 3,10 | 58,90 | 41,34 | 61,30 | 5 |
| SPC-1-065 | 65,00 | 45,00 | 14,00 | 6,35 | 3,35 | 59,30 | 40,60 | 62,50 | 5 |
| SPC-1-065/1 | 65,00 | 50,00 | 10,50 | 6,35 | 3,10 | 60,40 | 45,60 | 62,80 | 5 |
| SPC-1-070 | 70,00 | 50,00 | 14,50 | 6,35 | 3,35 | 64,20 | 45,84 | 67,50 | 5 |
| SPC-1-075 | 75,00 | 55,00 | 14,50 | 6,35 | 3,35 | 69,20 | 50,60 | 72,50 | 5 |
| SPC-1-080 | 80,00 | 60,00 | 14,50 | 6,35 | 3,35 | 74,30 | 55,80 | 77,50 | 5 |
| SPC-1-085 | 85,00 | 70,00 | 12,00 | 6,35 | 3,10 | 80,30 | 65,50 | 82,80 | 5 |
| SPC-1-090 | 90,00 | 70,00 | 14,50 | 6,35 | 3,35 | 84,15 | 66,10 | 87,50 | 5 |
| SPC-1-095 | 95,00 | 75,00 | 14,50 | 6,35 | 3,20 | 89,15 | 71,00 | 92,50 | 5 |
| SPC-1-100 | 100,00 | 80,00 | 14,50 | 6,35 | 3,35 | 94,15 | 75,84 | 97,50 | 7 |
| SPC-1-104 | 104,50 | 85,00 | 13,00 | 6,35 | 3,35 | 98,90 | 81,10 | 102,00 | 7 |
| SPC-1-105 | 105,00 | 85,00 | 14,00 | 6,35 | 3,35 | 99,42 | 80,60 | 102,50 | 7 |
| SPC-1-110 | 110,00 | 90,00 | 13,00 | 6,35 | 3,10 | 104,15 | 85,90 | 107,50 | 7 |
| SPC-1-115 | 115,00 | 95,00 | 14,50 | 6,35 | 3,35 | 109,90 | 90,50 | 112,50 | 7 |
| SPC-1-120 | 120,00 | 100,00 | 12,50 | 6,35 | 3,35 | 114,10 | 95,60 | 117,50 | 7 |
| SPC-1-125 | 125,00 | 105,00 | 12,50 | 6,35 | 3,35 | 119,15 | 101,00 | 122,50 | 7 |
| SPC-1-130 | 130,00 | 110,00 | 12,00 | 6,35 | 3,35 | 123,24 | 105,60 | 127,50 | 7 |
| SPC-1-150 | 150,00 | 125,00 | 14,00 | 6,35 | 3,35 | 143,00 | 120,60 | 147,30 | 7 |
| SPC-1-160 | 160,00 | 140,00 | 14,00 | 6,35 | 3,20 | 154,30 | 136,00 | 157,50 | 7 |
| SPC-1-200 | 200,00 | 180,00 | 14,00 | 6,35 | 3,10 | 194,00 | 175,60 | 197,50 | 7 |
SPC-1 is a three piece single acting sealing set which consists of onereinforced cotton fabric and nitrile rubber vulcanized together , one L shaped thermoplastic guide back-up ring and a retainingring.
PRODUCT ADVANTAGES
- Functions even with poor surfaces
- Limited space due to the open housing in one-piece piston
- Reinforced cotton fabric base prevents the seal from extrusion
- Good sealing at low pressures
APPLICATION
Mining equipment , after market , mobile hydraulics , presses andstandard cylinders.
| MATERIAL | |
| NBR | 80 SHORE A |
| COTTON FABRIC NBR | |
| POM | |
| OPERATING CONDITIONS | |||
| MEDIA | Mineral oils(DIN 51524) | HFA and HFB | HFC |
| TEMPERATURE | -30°C +105°C | +5°C +60°C | -30°C +60°C |
| PRESSURE | ≤500 Bar | ≤500 Bar | ≤500 Bar |
| SPEED | ≤0.5 m/sn | ≤0.5 m/sn | ≤0.5 m/sn |
Note: The above data are maximum values and cannot be used at the same time.
| SURFACE ROUGHNESS | Ra | Rmax |
| Sliding Surface ØD-Ød | ≤0.4 μm | ≤3.2 μm |
| Groove Base ØDb-Ødp | ≤1.8 μm | ≤6.3 μm |
| Groove Flanks B | ≤3.2 μm | ≤16 μm |
Note: It is recommended to have 50% to 90% of the working surface material contact area value.
INSTALLATION
Easily assembled into one-piece piston by hand. Open groove design gives an advantage for easy machining and reducing the machining costs. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation all individual parts of the seal must be oiled with system oil.