PRODUCTS
-
Hydraulic Sealing Elements
- SSE
- SSE/C
- SSA
- SSB
- SSN
- SSB-1
- SSG
- SSJ
- SSD
- SSM-1
- SSG-2
- SSO
- SSP
- SSQ
- SSD-3
Hydraulic Rod Sealing Elements
-
Pneumatic Sealing Elements
-
Guiding Elements
-
Static Sealing Elements
-
Special Sealing Elements
-
SealXpress Tailor-Made Machined Seals
SAN
| SEALX NO | d (f9) | D (H10) | b | B (-0/+0,5 | B1 (-0/+0, | D1 (-0,1/+ | r | c |
| SAN-012 | 12 | 22 | 10,4 | 13 | 7,7 | 24 | 1,1 | 1,5 |
| SAN-014 | 14 | 24 | 10,4 | 13 | 7,7 | 26 | 1,1 | 1,5 |
| SAN-016 | 16 | 26 | 10,4 | 13 | 7,7 | 28 | 1,1 | 1,5 |
| SAN-018 | 18 | 28 | 11 | 13 | 7,7 | 30 | 1,1 | 1,5 |
| SAN-020 | 20 | 30 | 10,4 | 13 | 7,7 | 32 | 1,1 | 1,5 |
| SAN-022 | 22 | 32 | 11 | 13 | 8,9 | 34,5 | 1,4 | 2 |
| SAN-025 | 25 | 35 | 11 | 13 | 8 | 37,5 | 1,4 | 2 |
| SAN-028 | 28 | 38 | 11,5 | 14 | 8 | 40,5 | 1,4 | 2 |
| SAN-030 | 30 | 40 | 11,5 | 14 | 8 | 42,5 | 1,4 | 2 |
| SAN-032 | 32 | 42 | 11 | 13 | 8 | 44,5 | 1,4 | 2 |
| SAN-035 | 35 | 45 | 11,5 | 14 | 8 | 47,5 | 1,4 | 2 |
| SAN-040 | 40 | 50 | 11 | 13 | 8 | 52,5 | 1,4 | 2 |
| SAN-045 | 45 | 55 | 11,5 | 14 | 8,6 | 58,2 | 1,8 | 2 |
| SAN-050 | 50 | 60 | 11,5 | 14 | 8,6 | 63,2 | 1,8 | 2 |
| SAN-063 | 63 | 75 | 13 | 16 | 9,6 | 78,2 | 1,8 | 2 |
SAN is a two piece single acting pneumatic rod seal which consists of one nitrile rubber sealing element and one polyester elastomer scrapper profile ring.
PRODUCT ADVANTAGES
- Good scrapping with special geometry and material
- High resistance to operating temperature changes
- Superior sealing effect
- Low static and dynamic friction values
APPLICATION
Pneumatic cylinders.
| MATERIAL | |
| NBR | 80 SHORE A |
| TPE | 55 SHORE A |
| OPERATING CONDITIONS | |
| MEDIA | Prepared , dried and de-oiled compressed air |
| TEMPERATURE | -30°C +105 °C |
| PRESSURE | ≤16 Bar |
| SPEED | ≤ 1.0 m/sn |
Note: The above data are maximum values and cannot be used at the same time.
| SURFACE ROUGHNESS | Rmax |
| Sliding Surface Ød | ≤4 μm |
| Groove Base ØD | ≤10 μm |
| Groove Flanks B | ≤15 μm |
INSTALLATION
It can be assembled into closed groove with tight hand force. SAN does not need additional element such as circlip for axial fitting within the housing. We recommend using special assembly tool. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation the rod seal must be oiled with system oil.
NOTES
For special applications that require high temperatures , SAN can be produced in combination of FKM and PTFE material.